RAAPA EXPO 2024, Russia
IMMERSIVE RIDES
Design points of amusement equipment
by：Jinma Rides
2022-08-21
Design points of amusement equipment
2018-07-17 00:51:2096
Although there are countless standardized rides on the market, designers always like to create their own designs, tailor-made for a particular playground and make it have its own characteristics. These special rides give the playground a unique. Building a play facility requires not only a fun, attractive design, but also ensuring that the facility is absolutely safe for children once built. The choice of basic materials is just as important as finishing the surface and adding parts that prevent falls. The following is a brief analysis of the design points of the new amusement equipment wholesale. Materials Construction of rides should be made of durable, hygienic, and easy-to-maintain materials. Neither potentially toxic substances nor unfinished metals (rusted or used for electrical wiring) should be used for rides. Metal must be painted, galvanized or treated to prevent rust. Wood is a good substitute for metal, but must be of the same kind without cracks, and in any case treated to prevent cracking and irregular breakage (not just the surface). If synthetic material is chosen, it must be durable and crack resistant. Surface finishing, especially on rough and uneven materials, is also one of the fundamental steps to reduce the risk of injury. Handrails and Railings Handrails and railings are the most common safety devices in amusement rides. Handrails and railings not only prevent falls, but holding them while walking also provides support and stability. Therefore, it should be designed in an easy-to-grip size according to relevant regulations. The height and diameter of the side protection facility is determined by its location, whether it is on a ladder, slope, walkway or raised platform, it must comply with the relevant local regulations for the relevant facilities. Boundaries Boundaries depend on the age of the ride users and the children's climbable heights. Thanks to the guardrails, the boundary stops children from falling from raised platforms and prevents them from climbing too high. Therefore, the design of the boundary should prevent climbing, standing or sitting on it. Therefore, the boundary should enclose the raised plane, leaving only an opening into and out of the platform. The opening should be smaller than the child's body so that the child does not slip or get caught in the crevice. The height of the boundary from the platform, ladder or slope surface should be at least 70 cm. Support Many rides have a support function, providing support for the hands and feet for grasping, balancing, and climbing. Effective handles should be sized and positioned for the child to grasp, securely attach the handles to the main structure, and prevent them from falling off and rotating. Seams, Screws, Edges These include the exterior edges of rides and the system of parts used to mount equipment. To be on the safe side, sharp edges, sharp shapes, and dangerous horns should be avoided. To ensure smooth surfaces of welded parts, the parts that anchor or support the structure should be strong and stable. The nails should fit flush into the main structure, the screws should be covered with plastic caps, and the protrusions should not exceed 8mm.
2018-07-17 00:51:2096
Although there are countless standardized rides on the market, designers always like to create their own designs, tailor-made for a particular playground and make it have its own characteristics. These special rides give the playground a unique. Building a play facility requires not only a fun, attractive design, but also ensuring that the facility is absolutely safe for children once built. The choice of basic materials is just as important as finishing the surface and adding parts that prevent falls. The following is a brief analysis of the design points of the new amusement equipment wholesale. Materials Construction of rides should be made of durable, hygienic, and easy-to-maintain materials. Neither potentially toxic substances nor unfinished metals (rusted or used for electrical wiring) should be used for rides. Metal must be painted, galvanized or treated to prevent rust. Wood is a good substitute for metal, but must be of the same kind without cracks, and in any case treated to prevent cracking and irregular breakage (not just the surface). If synthetic material is chosen, it must be durable and crack resistant. Surface finishing, especially on rough and uneven materials, is also one of the fundamental steps to reduce the risk of injury. Handrails and Railings Handrails and railings are the most common safety devices in amusement rides. Handrails and railings not only prevent falls, but holding them while walking also provides support and stability. Therefore, it should be designed in an easy-to-grip size according to relevant regulations. The height and diameter of the side protection facility is determined by its location, whether it is on a ladder, slope, walkway or raised platform, it must comply with the relevant local regulations for the relevant facilities. Boundaries Boundaries depend on the age of the ride users and the children's climbable heights. Thanks to the guardrails, the boundary stops children from falling from raised platforms and prevents them from climbing too high. Therefore, the design of the boundary should prevent climbing, standing or sitting on it. Therefore, the boundary should enclose the raised plane, leaving only an opening into and out of the platform. The opening should be smaller than the child's body so that the child does not slip or get caught in the crevice. The height of the boundary from the platform, ladder or slope surface should be at least 70 cm. Support Many rides have a support function, providing support for the hands and feet for grasping, balancing, and climbing. Effective handles should be sized and positioned for the child to grasp, securely attach the handles to the main structure, and prevent them from falling off and rotating. Seams, Screws, Edges These include the exterior edges of rides and the system of parts used to mount equipment. To be on the safe side, sharp edges, sharp shapes, and dangerous horns should be avoided. To ensure smooth surfaces of welded parts, the parts that anchor or support the structure should be strong and stable. The nails should fit flush into the main structure, the screws should be covered with plastic caps, and the protrusions should not exceed 8mm.
Custom message
Related Products
